Hubei Cheng Li independently developed and manufactured sewage treatment truck, won the national patent, energy saving and environmental protection. Hubei
Chengli sewage treatment vehicle which configuration?
 Â
The basic configuration of the sewage treatment vehicle: sandwich power take-off, gear pump, multi-way valve, plunger motor, sewage discharge
Pump, water ring vacuum pump, shaftless screw, auger, suction pipe, motor, power distribution box, wire winch and other groups
Together.
The sewage treatment vehicle adopts Dongfeng Furuicha chassis with chassis configuration: 3.3m wheelbase, 7.00-10 nylon
Tire, 3 tons rear axle, 1.5 tons front axle, 5- speed gearbox and steam brake. The length of the vehicle is 5.995 meters wide
It is 1.99 meters and its height is 2.65 meters. The exterior of the sewage treatment vehicle is designed with 6 roll-open doors and 4 waste compartments. rear
Use double doors and LED advertising billboards for easy operation and promotion. 
The model number of the sewage truck is CLW5040TWC4 , which can be used on the blue card and can be applied to domestic first-tier cities.
City work.
The conventional configuration of the sewage treatment truck: There are four 80 suction pipes , each 7 meters long, totaling 28 meters.
There is a roll of 100 meters of wire, the actual length is 95 meters, of which 5 meters for the distribution box to the motor and wire winding
Disk, the remaining 90 meters for connecting to external power.
Sewage vehicles use dual power, that is, if there is no external power supply, the owner of the vehicle can be used.
The machine operates; if there is an external three-phase power supply, it can be connected to the motor using the configured wires.
operation. As long as there is a power supply, it is better to use an external power supply to operate the motor, because the use of electricity is definitely better than using diesel.
The machine is cheap, and the wear of the motor is much smaller than that of the diesel engine. This allows the customer group to save most of the time.
The capital, which is also a major advantage of sewage treatment vehicles, can be mentioned in the promotion.
Sewage treatment vehicle operating process (working principle) : first get in and out of the suction pipe. Into the tube to be put
In a septic tank or a lagoon that needs to be disposed of, the discharge pipe should be placed on the sewer pipe nozzle or in an appropriate location.
If it is to use the host operation, first start the host that is diesel, when the barometer pointed to 6 bar
, Depress the clutch pedal; then open the switch of the PTO, then slowly release the clutch pedal
Board, so that the sewage treatment vehicle is in operation; then slowly pull the hand throttle cable to check the drive
The tachometer in the drive room controls the engine speed between 1200-1400 revolutions.
Why control between 1200-1400 rpm ? Because the car's sewage pump and vacuum pump speed
It is 1450 rpm, which is configured according to the rotation speed of the motor. The speed ratio of the center power take-off is 1:1.2 . and also
That is, when the engine speed reaches 1200 rpm, the sewage pump can reach a speed of 1440 . Engine such as
If the speed reaches 1400 , the sewage pump can reach a speed of 1680 , and more than 1400 rpm will exceed the sewage
The normal speed of the pump, so you need to control the engine speed between 1200-1400 , can not exceed
Can not be lower than this speed , low speed can not achieve the desired effect. The high speed is beyond the sewage pump and vacuum pump
Normal range may cause damage.
After the engine speed is controlled, open the multi-way valve. This multi-way valve is used to control the auger.
The non-shaft spiral of the surface can compress the sucked dirt and separate the water and the material.
The water comes out through the sewage pump. Dirt is discharged from the rear door of the chamber.
If you are using motor power, you need to connect the three-phase power supply. The three fire wires and the neutral wire must be connected because
Leakage protectors are installed in the power distribution box inside the vehicle and will automatically trip if there is an electric shock. Distribution box
There is also an anti-reverse protection device inside, which means that no matter how three-phase power is connected, it will not be reversed. Pick up
The power supply then plugs the power distribution box into the socket of the wire winch. Just connect the power supply, the power distribution box
The indicator will light, then press the switch button, so that the vehicle will enter the operating state, other operations with the
Host operation is the same.
Cheng Li Special Purpose Vehicle Co., Ltd. Wang Xinqun provided a friendship to learn more about Cheng Li’s new products or sewage
Processing vehicle information can be phoned. Manager of 18672222488 Wang. Fax: 0722-
3220988. Hope to be able to
Exchange to help you buy a car. You can also refer to Cheng Li’s designated sales website:
.
Huixian Mishan Graphite Company can produce kinds of Graphite Products. The popular product is Graphite Crucible. The large size graphite crucible is widely used in metallurgy. The diameter can reach 800mm. This type graphite crucible always use the fine grain type graphite material and the electrode type graphite material. Since the size is too large but there is no large size high pure type graphite material and it will be very expensive. Fine grain type graphite material is enough for the use. For smaller type graphite crucible, you can choose the graphite material as need.
Graphite Melting Crucible, Graphite Crucible, Melting Silver Graphite Mold,Raw Graphite Rounds
Huixian City Mishan Graphite Jip Co., Ltd. , https://www.msgraphitemold.com