The safety of the machine operator depends to a large extent on whether or not the operator carefully implements safety procedures. To ensure safety, the operators do:
First, the operator must be familiar with the characteristics of the use of machine tools and safety operating procedures, regular safety technicians on the operation of education and inspection of safety operation skills.
Second, the operator should wear appropriate tight protective clothing, fasten the cuffs or roll up the sleeves, put the shirt in the pants, the belt should not be suspended. Do not go through a fat shirt or jacket with a wide collar. When wearing long hair, wear a protective cap or headscarf. The headscarf and tie must be carefully stoppered.
Third, the operator should wear anti-strike eyewear in three ways: hard glass eyepieces, glued glass goggles, steel mesh goggles. Its characteristic is that it is not easy to break, it is cracked when it breaks, it does not splash, so it is not easy to hurt the eye. Should use no bubble, impurities, smooth flat surface mirror, so as not to wear when you feel unclear, dizziness, affecting vision. Also pay attention to whether the lens and frame are connected firmly, whether the frame is smooth and sharp, so as not to cause scratches or oppression, the color can not be monochrome, use mixed colors, such as yellow-green, blue-green, gray comparison it is good.
Fourth, before starting the bed, it is necessary to check in detail whether the protective devices for the dangerous parts on the machine tool are safe and reliable, lubricate the machine tools, and do no-load tests.
5. When working, the workplace should be kept clean and orderly. The workpieces to be machined and processed shall be placed on shelves or in special equipment. The workpieces or tools shall not be placed on the machine tools, especially on the moving parts of the machine tools and the passages of the working places, so as to prevent the materials from falling and hurting.
6. The tools and tools must be securely clamped to prevent the workpiece and tool from falling out of the fixture. Lifting equipment should be used when handling bulky parts.
7. When the machine tool is running, it is forbidden to adjust the machine tool or measure the workpiece by hand; the handle elbow shall not be supported on the machine tool, and the rotary part of the machine tool must not be touched by hand; and the installation and protection device shall not be removed. Do not remove the chips by hand and use hooks, brushes, or special tools to remove the chips.
8. When the machine tool is running, the operator cannot leave the work site. When the machine tool is found to be malfunctioning, it should be stopped immediately. Please check with the maintenance worker. When the power supply is stopped, immediately shut down the machine or other electric mechanism and take the tool out of the working area.
Nine, do not mix dirt or waste oil into the machine coolant, otherwise it will not only foul the coolant, but will even spread the disease. In order to prevent skin diseases, it is forbidden to wash hands with emulsified oil, kerosene, and oil.
10. When the chip splashes are serious, the compressed air must be used to eliminate the chips. In order not to harm other operators, a baffle should be installed around the machine to isolate the operating area. The pressure of the compressed air should be as low as possible. Do not use compressed air to blow off dust or dirt on the clothes or hair, as this may cause damage to the ears and eyes.
11. When the work is completed, the machine tool and motor should be turned off. The tool and workpiece should be withdrawn from the work position. Clean the used work tools, clamps, and measuring tools, and carefully clean the tool.
First, the operator must be familiar with the characteristics of the use of machine tools and safety operating procedures, regular safety technicians on the operation of education and inspection of safety operation skills.
Second, the operator should wear appropriate tight protective clothing, fasten the cuffs or roll up the sleeves, put the shirt in the pants, the belt should not be suspended. Do not go through a fat shirt or jacket with a wide collar. When wearing long hair, wear a protective cap or headscarf. The headscarf and tie must be carefully stoppered.
Third, the operator should wear anti-strike eyewear in three ways: hard glass eyepieces, glued glass goggles, steel mesh goggles. Its characteristic is that it is not easy to break, it is cracked when it breaks, it does not splash, so it is not easy to hurt the eye. Should use no bubble, impurities, smooth flat surface mirror, so as not to wear when you feel unclear, dizziness, affecting vision. Also pay attention to whether the lens and frame are connected firmly, whether the frame is smooth and sharp, so as not to cause scratches or oppression, the color can not be monochrome, use mixed colors, such as yellow-green, blue-green, gray comparison it is good.
Fourth, before starting the bed, it is necessary to check in detail whether the protective devices for the dangerous parts on the machine tool are safe and reliable, lubricate the machine tools, and do no-load tests.
5. When working, the workplace should be kept clean and orderly. The workpieces to be machined and processed shall be placed on shelves or in special equipment. The workpieces or tools shall not be placed on the machine tools, especially on the moving parts of the machine tools and the passages of the working places, so as to prevent the materials from falling and hurting.
6. The tools and tools must be securely clamped to prevent the workpiece and tool from falling out of the fixture. Lifting equipment should be used when handling bulky parts.
7. When the machine tool is running, it is forbidden to adjust the machine tool or measure the workpiece by hand; the handle elbow shall not be supported on the machine tool, and the rotary part of the machine tool must not be touched by hand; and the installation and protection device shall not be removed. Do not remove the chips by hand and use hooks, brushes, or special tools to remove the chips.
8. When the machine tool is running, the operator cannot leave the work site. When the machine tool is found to be malfunctioning, it should be stopped immediately. Please check with the maintenance worker. When the power supply is stopped, immediately shut down the machine or other electric mechanism and take the tool out of the working area.
Nine, do not mix dirt or waste oil into the machine coolant, otherwise it will not only foul the coolant, but will even spread the disease. In order to prevent skin diseases, it is forbidden to wash hands with emulsified oil, kerosene, and oil.
10. When the chip splashes are serious, the compressed air must be used to eliminate the chips. In order not to harm other operators, a baffle should be installed around the machine to isolate the operating area. The pressure of the compressed air should be as low as possible. Do not use compressed air to blow off dust or dirt on the clothes or hair, as this may cause damage to the ears and eyes.
11. When the work is completed, the machine tool and motor should be turned off. The tool and workpiece should be withdrawn from the work position. Clean the used work tools, clamps, and measuring tools, and carefully clean the tool.
Led Bulb Adhesive,Silicone Led Bulb Adhesive,Silicone Rubber Adhesive Sealant,Rtv Silicone Adhesive
Guangdong Shengtang New Material & Technology Co.,Ltd. , https://www.shengtang-silicone.com