Ship launching airbags are to be constructed of a cylindrical body and two conical heads (one at each end). Ship launching airbags with lots of advantages, such as easy to operate, time saving, saving investment safety, etc.
Major Strengths of Ship Launching Airbags:
High level of safety: Equipped with a reliable safety valve, our airbags can stand the maximum pressure up to 4 times that of the operating pressure.
Good air tightness: Pressure decreases less than 10% for a period of 24 hours.
Long lifespan: It is guaranteed that our airbags can sustain their designed operating pressure for 3 years.
Specification
1. Structure
2. Diameters: 0.8 m - 2.0 m or customized.
3. Length: 6 m - 20 m or customized.
4. Loading Capacity: about 10 T/M to 40 T/M.
5. Grades:
Ordinary airbags - 3, 4 or 5 layers of synthetic-tire-cord.
High bearing capacity airbags - 6, 7 or 8 synthetic-tire-cord.
Super high bearing capacity airbags - 9, 10 or more layers of synthetic-tire-cord.
6. Accessories: Pull ring, iron airlock, tee joint, pressure gauge, ball valve, hose joint etc.
7. Technical Data of Ship Launching Airbags
| Model | Diameter (m) |
Initial pressure (KPa) |
Rated working pressure, Pe (KPa) |
Bearing capacity (kN/m) | Minimum burst pressure (KPa) |
| QP3 | 0.8 | 25 | 130 | 114 | 390 |
| 1.0 | 18 | 100 | 110 | 300 | |
| 1.2 | 15 | 85 | 112 | 260 | |
| 1.5 | 13 | 70 | 115 | 210 | |
| QP4 | 0.8 | 35 | 170 | 149 | 510 |
| 1.0 | 25 | 130 | 143 | 390 | |
| 1.2 | 20 | 110 | 145 | 330 | |
| 1.5 | 16 | 90 | 148 | 270 | |
| 1.8 | 14 | 80 | 158 | 240 | |
| QP5 | 0.8 | 48 | 210 | 184 | 630 |
| 1.0 | 35 | 170 | 186 | 510 | |
| 1.2 | 28 | 140 | 185 | 420 | |
| 1.5 | 20 | 110 | 181 | 330 | |
| 1.8 | 16 | 90 | 178 | 270 | |
| QP6 | 1.0 | 45 | 200 | 219 | 600 |
| 1.2 | 32 | 165 | 217 | 490 | |
| 1.5 | 25 | 130 | 215 | 390 | |
| 1.8 | 20 | 110 | 218 | 330 | |
| Note: 1. Rated working pressure:±5%. 2. Compress deformation: ±2%. 3. Bearing capacity: one meter airbag at a deformation rate of 70%, internal pressure equivalent to the rated pressure value of Pe. | |||||
9. Rubber Material Test:
| No. | Test item | Required value | Test method | |
| 1 | Tensile Strength, MPa | ≥ 18 | ISO37 | |
| 2 | Elongation at break, % | ≥ 400 | ISO37 | |
| 3 | Hardness, shore A | 60±10 | ISO7619-1 | |
| 4 | Tear Strength N/cm | ≥ 400 | ISO34-1 | |
| 5 | Compression set, % (70 ºC ± 1 ºC, 22 h) | ≤ 30 | ISO815-1 | |
| 6 | After thermal aging at (70 ºC, ±1 ºC, 96 h) |
Holding of pull lengthening,% | ≥ 80 | ISO188 |
| 7 | Holding of elongation at break,% | ≥ 80 | ISO188 | |
| 8 | Change of hardness, hardness | ≤ 8 | ISO7619-1 | |
| 9 | Static ozone aging at 40 ºC*96 h, {ozone concentration( 50±5)*10} |
No crack | ISO1431-1 | |
10. Reinforcing Material: the warp should be (90±5) cord per 100 mm in width, and the breaking strength shall be more than 205 N per cord.
Â
11. Appearance: The appearance of an air bag shall be smooth, glossy and without blemish such as crack, blister, delamination pits or impurities.
Â
12. Dimensional Tolerances:
The length and diameter of an airbag shall be measured with the rated working pressure and be within ±3%.
Â
13. Ship Launching Airbags Performance:
| D (M) |
(4-5 layers) | (6-8 layers) | Â | ||
| Initial pressure (MPa) |
Working pressure (MPa) |
Initial pressure (MPa) |
Working pressure (MPa) |
 | |
| Â | |||||
| 1.0 | 0.14 - 0.16 | 0.12 - 0.14 | 0.22 - 0.26 | 0.20 - 0.24 | Â |
| 1.2 | 0.12 - 0.14 | 0.10 - 0.12 | 0.20 - 0.24 | 0.17 - 0.22 | Â |
| 1.5 | 0.10 - 0.12 | 0.08 - 0.10 | 0.15 - 0.20 | 0.13 - 0.18 | Â |
| 1.8 | 0.08 - 0.10 | 0.07 - 0.09 | 0.13 - 0.16 | 0.11 - 0.14 | Â |
| 2.0 | 0.07 - 0.09 | 0.06 - 0.08 | 0.12 - 0.15 | 0.10 - 0.13 | Â |
Â
Excavator Hydraulic Pump
1. Excavator Hydraulic Pump Moldel
Excavator piston pump and Travel Motor : SPK10/10(E180,E200B), SPV10/10(MS180-3,MS180-8,EL240), VRD63(E110B,E120B), AP12(320,E315), A8VO107(320B,E300L,E325L), A8VO160(E330B,E345L), ,A8VO107(320B,E300L,E325L), A8VO160(E330B,E345L), CT12G,CT14G,CT15G,CT16G
2. Geniune / Original Rebuilt Excavator Hydraulic Pump Manufactures
REXROTH excavator piston pump and travel motor
1, A8VO: A8VO55, A8VO80,
A8VO107, A8VO160
2, A2F: A2F23, A2F28, A2F55, A2F80, A2F107, A2F160
3, A4VSO: A4VSO40, A4VSO45, A4VSO56, A4VSO71,
A4VSO125, A4VSO180,
A4VSO250, A4VSO355
4, A4VG:A4VG28, A4VG45, A4VG50, A4VG56,
A4VG71, A4VG125, A4VG180, A4VG250
5, A6V: A6V55, A6V80,
A6V107, A6V160, A6V225, A6V250
6, A7V: A7V16, A7V28, A7V55, A7V80, A7V107,
A7V160, A7V200, A7V250
7, A8V: A8V55, A8V80, A8V107, A8V115, A8V172
8, A10VSO: A10VSO28, A10VSO43, A10VSO45,
A10VSO71, A10VSO100, A10VSO140
9, A10VD: A10VD17, A10VD21, A10VD28, A10VD43, A10VD71
10, A11V: A11V130, A11V160, A11V190, A11V250
11, AP2D21, AP2D25, AP2D36, AP2D38
EATON:3321/3331, 4621/4631, 5421/5431, 7621
VIKERS:PVE19, PVE21, PVH57, PVH74, PVH98, PVH131, PVB5/6,PVB10
NACHI: PVD2B: PVD2B-34, PVD2B-36, PVD2B-38, PVD2B-40,
PSV2: PSV2-55(SH100/120)
VOLVO: F11-5, F11-10, F11-14 , F11-19,F11-58 , F11-60, F11-80, F11-90
, F11-110, F11-150, F11-250
KAYABA : MAG120, MAG150, MAG170, MAG200, MAG230
LINDE: B2PV50(BPR50), B2PV75(BPR75), B2PV105(BPR105) ,BPR140,BPR186
TAIJIN: GM07,GM08,GM19,GM23,GM24,GM28,GM30F,GM30H,GM30VA,GM35VA,GM38H,GM38VA
3. Excavator Replaced Hydraulic Pump South korea, Japan Brand Replacement
KYB MAG series(MAG-18,MAG-26,MAG-33,MAG-85,MAG-170)
Kawasaki K3V K5V series
Nachi PVD series (PVD-1B,PVD-2B,PVD-3B)
Another Excavator Parts We also Supplied.
Excavator parts: Excavator Engine Part, Excavator Undercarriage Parts, Excavator Final Drive, Excavator Main Valve , Excavator hydraulic pump.
Excavator Hydraulic Pump
Excavator Hydraulic Pump,Excavator Pump,Hitachi Excavator Hydraulic Pump,Kawasaki Hydraulic Pump
Jining Kunpeng Construction Machinery Equipment Co., Ltd , https://www.excavatorenginepart.com