Winter has arrived. The warm car is a reliable guarantee for our usual travel. What if the car has insufficient heating? If you do not want to get cold shiver!
The Auto Loading Network reporter learned from the after-sales maintenance department of the car dealer that the lack of a vehicle warm air system is divided into two reasons. One is the engine cooling system, and the other is the cause of the poor operation of the heater control mechanism. When repairing, first determine what the cause is and then perform appropriate repairs.
The method of discrimination is very simple. Look at the temperature of the two inlet pipes of the small warm water tank. If the two pipes are hot enough, it means that the air volume control mechanism is a problem. On the contrary, if the two water pipes are cool, or it is a hot one. Cool, indicating the problem of the cooling system.
Possible problems with the cooling system:
1. The thermostat is normally open or the thermostat is opened prematurely, which causes the cooling system to prematurely cycle. The outside temperature is very low. Especially when the car runs up, the cold wind quickly cools the antifreeze . The engine water temperature is not Come, the warm wind will not be hot.
2. The impeller of the pump is damaged or thrown away, so that the flow through the small tank of warm air is not enough, and the heat cannot come.
3, the engine cooling system has air resistance, air resistance leads to poor circulation of the cooling system, resulting in high water temperature, warm air is not hot fault. If the cooling system always has gas, it is likely that the cylinder pad is damaged to the cooling system; if the inlet pipe of the warm water tank is hot, and the outlet pipe is cool, this situation should be a blockage of the small warm water tank. Should replace the heater small water tank.
Air volume control mechanism issues:
1, the car's warm air is the use of a blower to blow the heat of the small heating tank into the cab, if the air volume is not enough or cold and hot air distribution is not good, so that the heat of the small heat tank water distribution does not come out, can also cause warm air The temperature does not come. In this case, first check the filter for dirty plugging, clean it up, and replace it if necessary.
2. Check the operation status of each position of the blower, and each gear must reach a sufficient speed. If the knob is adjusted to the warm air position, the air volume is large enough, the wind direction is normal, and the cool air is blown out. Check whether the control flap pull wire of the hot air box is off, whether the warm air impeller is damaged, whether the flap is detached, etc. The warm air will heat up after troubleshooting.
Storage Upright Roll Forming Machine
The rack roll forming machine includes one decoiler, servo feeder, hydraulic punching, roll forming and hydraulic cutting. The products of the rack roll forming machine are used as racks and shelves for supporting the daily commodities in supermarkets and shops.
1.Fast speed
2.Elegant appearance
3.PLC control, full automatic
4.Manufacture as buyer's requirements
Specifications:
Raw material
Colored steel, Galvanized steel
Material thickness range
1.5-3.0mm
Rollers
18-24 rowa(according to drawings and size)
Material of rollers
45# steel with chromed
Shaft diameter and material
80mm, material is 40Cr
Material of cutting blade
Cr12 mould steel with quenched treatment
Forming speed
6-8m/min(include the punching)
Way of driven
Chain transmission or Gear box
Controlling system
Siemens PLC
Main motor power
15KW
Hydraulic station power
11KW
Voltage
380V/3Phase/50Hz or at buyer's request
Size of the machine
L*W*H 12m*2.0m*1.6m
Working process:
Decoiler - Seven rollers leveling - Servo feeding - Power press - Material guiding - Main roll forming machine
- PLC control system - Hydraulic cutting (45°) - Receiving table
Pictures for machine:
Training and Installation :
1. We offer installation service local in paid, reasonable charge.
2. QT test is welcome and professional.
3. manual and using guide is optional if no visiting and no installation.
Certification and after service:
1. Match the technology standard, ISO producing certification
2. CE certification
3. 12 months warranty since the delivery. Board.
Our advantage:
1. Short delivery period.
2. Effective communication
3. Interface customized.
Storage Upright Roll Forming Machine,Storage Racking Upright Roll Forming Machine,Lms Storage Upright Roll Forming Machine,Punchig Storage Upright Roll Forming Machine
YingYee Machinery and Technology Service Co.,Ltd , https://www.yingyee.cn